SUPPLIES & TOOLS:
- Pouf
- 1 1/2yd fleece
- 5lbs Polyfil® (more might be needed depending on preferred firmness)
- Basic sewing supplies
- Play Mat
- 1yd main fabric
- 1yd backing
- 1 1/2yd binding
- 1yd heavyweight batting
- Crib Sheet
- 2yds crib fabric
- 1/4" elastic, 1 pkg
- 16"x 8" & 14" Square Pillow
- 1yd Winnie the Pooh fabric
- 1yd coordinating Winnie the Pooh fabric for binding
- 14"x 14" pillow form
- Filler cord for piping, 1 pkg
- Polyfil, 1 pkg
- Basic sewing supplies
DIRECTIONS: (1/2" seam allowance)
- Pouf
- Cut (2) 21" circles from fleece.
- For the side, cut (1) 17"x width of fabric and (1) 17"x 6-8" (to measure 66" when the two pieces are sewn together.)
- Sew the side pieces together to form tube leaving an opening for turning and stuffing.
- With RST, pin and sew the side to the top of pouf.
- With RST, pin and sew the bottom of the pouf to the side.
- Turn and stuff.
- Play Mat
- Cut 34" circle from main fabric, backing and batting.
- Layer backing, with right side towards table, batting, and main fabric wrong side down.
- Pin and baste raw edges.
- Pin center and quilt as desired.
- For the binding, open fabric and lay flat. Cut strips 8" wide (cut on the bias). You need enough strips to measure 4yds.
- Sew strips together.
- Fold and press binding in half lengthwise.
- Fold both long edges into center and press.
- Pin binding over edge of mat covering the mat 2" all around outside.
- Sew along the edge of binding.
- Crib Sheet
- Lay out fabric flat on table.
- The selvage will not be cut off. It will not be seen in the folds.
- Cut out an 8" square all 4 corners.
- Start with one of the corners, fold the fabric so that the printed sides of your fabric is touching, and stitch 1/4" seam.
- Continue with the remaining corners.
- Press 1/4" around the outside of crib sheet.
- Press again 1/2" around for elastic casing.
- Mark with a pin 10" on each side of the corner seams.
- Starting and stopping at each pin and leaving a 1" opening (for inserting elastic) stitch around the sheet.
- Cut (4) 12" pieces of elastic. (Elastic will be inserted in casing at corners only.)
- Starting at one corner, thread the elastic through the corner casing opening.
- Pin in place and stitch over ends to secure.
- Stitch opening closed at corners.
- Pillows
- 16"x 8" Pillow
- Cut (2) 17"x 9" for front and back of pillow.
- Cut 2" strips for piping to measure 1 1/2"yds when short ends are sewn together.
- Make piping and sew to front of pillow.
- With RST, stitch front to back leaving an opening for stuffing.
- Turn and stuff.
- Sew opening closed.
- 14" Square Pillow
- Cut (1) 15"x 15" square and (2) 10"x 15" rectangles for back.
- Cut 2" strips for piping to measure 2yds when short ends are sewn together.
- Make piping and sew to front of pillow.
- Hem one long edge of both of the back rectangles. Fold 1/4" under and press and fold 1/4" again press and sew.
- With RST, pin back pieces to front overlapping pieces in center.
- Stitch around outside edge.
- Turn and insert pillow.