SUPPLIES & TOOLS:
- Cotton Fabric
- Basic Sewing Supplies
- Mask Pattern
DIRECTIONS:
- Download the pattern by clicking “download PDF" below Print Description.
- Cut your pattern from your fabric.
- Cut pieces that will create the side channels and the strap. The side channels should measure 4.25 inches by 2.5 inches. The strap should be 40 inches long and two inches wide.
- Sew your strap. Iron the strap in half, then fold the two sides again to meet the centerfold. Then fold again along the original centerfold and press. Similar to making double-fold bias tape, topstitch along the open edge using matching thread. At the ends of the strap, fold up a half inch and top stitch to secure.
- Next prep your side channels. Fold the short edges down a half-inch, press, and topstitch using coordinating thread. Then fold them in half longways, wrong sides together.
- With right sides together, sew two mask pieces along the center seam. Repeat with the other two mask pieces.
- You should now have two mask pieces. pin them right sides together. Stitch using a 3/8 inch seam allowance along the top and bottom of the mask, be sure to leave a two to three inch opening along the bottom.
- Now take your side-channel pieces and arrange them into the open sides of the mask. Your raw edges should all line up so that the channel pieces are tucked into the mask. Sew the sides using a 5/8 inch seam allowance.
- Turn your mask right side out and press.
- Topstitch around the perimeter of your mask using matching thread, being sure to catch the opening you left on the bottom.
- Thread the strap you made through the channels using a safety pin if needed.
Rated 2 out of
5
by
toots from
Great pattern to download
Sorry to say I can't print the directions to any of these patterns. The patterns themselves download and print perfectly. Can't see the video on these either. Someone needs to get on your website and fix the problem.
Date published: 2020-09-30
Rated 2 out of
5
by
proutyn from
pattern size?
I printed off the pattern, but it is very small. The ruler on the side of the pattern shows it being 4 inches, but actual ruler size measures out to be only 3 inches. Maybe I printed the wrong PDF?
Date published: 2020-08-18
Rated 2 out of
5
by
MaskMaker from
To much space gap on either side of nose.
I’ve personally only been sewing full face pleated masks with metal strip encased in seam at the nose for a super snug fog free eyeglasses fit, and that’s all I’ll wear for the best coverage. I had one customer who requested this style and I went against my better judgement and agreed to make it. Yes, it’s a cleaner prettier look than the pleated which shows off a cute fabric print. It fits well under chin and at sides, BUT, it does NOT fit properly at the nose and sides of nose on upper cheek area. There’s no way to insert a flat metal surgical mask style strip (which I insert on my pleated masks and everyone loves). You might be able to thread a pipe cleaner into the seam allowance, but those don’t last long. This mask has too much movement at the top edge on the face, since the top edge is not fitted, it just slides up and down, partially exposing sides of nostrils. If you don’t have to speak while wearing it, less aerosol will escape. It definitely won’t do anything to protect YOU from others’ aerosols. This is just an OK mask, better than nothing if you are not good at sewing several layers with pleats for the pleated style. But if you want a mask offering better blockage of aerosols escaping, go with pleated style, with a metal strip pinched at the nose. Another observation, because I made a few and had my family test them before I’d ever think of selling any- the movement from the jaw pulling the mask down along the nose, cause friction on the skin and my son, who breaks out easily, had irritation while wearing this mask that I made using 100% cotton that I prewashed. One more note: since this style has the center front seams right in front of the nose and mouth, you might want to add a filter since you have all those holes from stitches. And use the tiniest stitch setting you can to reduce the hole space. My nurse friends will not wear this style. I will only make these on special request after I point out the flaws.
Date published: 2020-08-16
Rated 5 out of
5
by
MaryJane from
Pattern IS there.....check again!
The link to the pattern shows up right under the photo of the individual mask style. It looks pretty easy and I'm anxious to try it out with fabric I justbought at JoAnn's. I'vebeen looking for a pattern that dips down under the eyes. This looks like it will work.
Date published: 2020-08-15
Rated 5 out of
5
by
Deb W from
Nice mask with multiple fit options
Nice fit and design works well with both geometrics & florals. I added a nose wire (sew channel in the top, insert 6” non-rusting nose wire, stitch channel closed then finish sides) to improve seal. I’m making multiples so copied the pattern into a piece of plastic. Makes cutting with a rotary cutter a breeze!
Not sure why others had problems downloading. The link is *right there* below the picture.
Date published: 2020-08-15